| Channel Strips |
|
| EQ |
Assigns EQ editor for selected channel across channel knobs. Use Channel Bar Scroll buttons to access additional parameters. |
| Insert |
Assigns Plug-in Editor for selected channel across channel knobs. Use Channel Bar Scroll buttons to access plug-in parameters. |
| Send |
Assigns Sends for selected channel across channel knobs. |
| Record |
Arms the assigned audio track of the Channel. |
| Solo |
Solos the Channel. |
| Mute |
Mutes the Channel. |
| Auto |
Cycles through Read/Write Mode on track |
| Select |
Sets the Channel to the Select state. |
| Knob |
Changes the assigned parameter. |
| Knob Button |
|
| Track Meters |
Displays Stereo metering for tracks. |
| Bank Mode |
|
| The assignment buttons are used to assign controls to the Knobs. |
|
| Pan (Default) |
Shows pan position in LED Strip. Knob controls pan position. |
| Send A |
Assigns Send 1 to knobs. Assigns Send 6 to knobs when F-J is enabled. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send B |
Assigns Send 2 to knobs. Assigns Send 7 to knobs when F-J is enabled. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send C |
Assigns Send 3 to knobs. Assigns Send 8 to knobs when F-J is enabled. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send D |
Assigns Send 4 to knobs. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send E |
Assigns Send 5 to knobs. Use Channel Bar Scroll Left and Right to switch parameters. |
| F-J |
Toggles between Sends 1-5 and 6-8 for A-E buttons. |
| Send parameters |
1st parameter is Send level. |
|
2nd parameter is bypass for Send assignment. |
|
3rd parameter is Pre/Post. |
|
4th parameter is pan for send. |
|
5th parameter is Send assignment. |
|
6th parameter is Master send bypass for channel. |
| Input, Output |
Assign channel parameters to knobs. Use Channel bar scroll Left and Right to cycle through parameters. |
| Channel Parameters |
1st parameter is channel output. |
|
2nd parameter is input monitoring on channel. |
|
3rd parameter is channel input. |
|
4th parameter is pre-gain. |
|
5th parameter is phase invert. |
| Soft Keys |
Assigns knob buttons on Channel strips to be soft key buttons. |
| Flip |
Flips knobs to faders. |
| Master Faders |
Press once to enable Master Fader control. Press a second time to enable V-Window mode for the 24th channel fader. Press a 3rd time to cycle back to basic channel control. |
| Output Meters |
Displays the Master Meter. |
| Automation |
|
| Write |
Toggles Write automation for all channels. |
| Touch |
Sets Automation to Touch automation for all channels. When in Touch mode, pressing again enables Cross-over automation mode. |
| Latch |
Sets Automation to Latch mode for all channels. When in Latch mode, pressing again enables Cross-over automation mode. |
| Read |
Toggles Read automation for all channels. |
| Write To Start |
Enables Write to Start Automation. |
| Write To End |
Enables Write To End Automation. |
| Write To All |
Enables Loop Automation. |
| Auto Suspend |
Suspends Automation |
| There is no indication if Automation enables are On/Off |
|
| Vol |
Toggle Enable Volume Automation |
| Pan |
Toggle Enable Pan Automation |
| Mute |
Toggle Enable Mute Automation |
| Sends |
Toggle Enable Sends Automation |
| EQ |
Toggle Enable Send Mute Automation |
| Plugin |
Toggle Enable Plugin Automation |
| Transport |
|
| Play |
Starts playhead at current position in Timeline. |
| Stop |
Stops playhead at current position in Timeline. |
| Record |
Starts Record Mode for playhead |
| Rewind |
Move playhead backwards in Timeline. |
| Fast Forward |
Moves playhead forward in Timeline. |
| RTZ |
Returns playhead to beginning of Timeline. |
| Shift+RTZ |
Sends playhead to end of Timeline. |
| Pre Roll |
Enables Pre Roll |
| Post Roll |
Enables Post Roll |
| Mark In |
Sets start point of selection in Timeline. |
| Mark Out |
Sets end point of selection in Timeline. |
| Loop Play/Loop Rec |
Toggles Loop mode for loop selection in Timeline. |
| Quick Punch |
Toggles Punch mode for selection in Timeline. |
| Counter |
Displays Counter for current session. Counter mode can be changed in DAW. |
| Automatic TalkBack |
This C24 feature is supported. Enable/disable on C24 by pressing Utility button. |
| Edit |
|
| Copy |
Copy Selected Region |
| Copy+Option |
Cut Selected Region |
| Copy+Shift |
Delete Selected Region |
| Copy+Control |
Duplicate Selected Region |
| Copy+Command |
Separate Region at Playhead |
| Paste |
Paste Region |
| Utility |
|
| Save |
Save the current session. |
| Undo |
Undo the last action. |
| Redo |
Redo the last action. |
| Window Buttons |
|
| Mix |
Opens MixConsole Window |
| WinCfg |
Opens Status Window |
| Memloc |
Opens Memory Locator Window |
| Navigation |
|
| Bank Left |
Banks tracks left/Scrolls 1 track left in Nudge mode |
| Bank Right |
Banks tracks right/Scrolls 1 track right in Nudge mode |
| Nudge |
Toggles Nudge mode On/Off |
| There are several different modes available for the cursor keys and wheel. |
|
| Scrub |
Enables Scrub mode for the wheel. |
| Shuttle |
Enables Shuttle Mode for the wheel. |
| Navigate/Nav |
Enables Marker Mode. Use Wheel or Left/Right cursor keys to navigate between markers. Down cursor key creates marker at playhead. |
| Zoom |
Enables Zoom mode for the wheel and cursor keys. |
| Zoom+Shift |
Enables Track Zoom for the wheel and cursor keys. Track zoom increases/decreases track height. |
| Zoom+Option |
Enables Wave Zoom for the wheel and cursor keys. Wave zoom increases waveform view in region. |
| Trim |
Enables Nudge trim mode for the wheel and cursor keys. Use Left/Right cursor keys to change between start/end of region. Use Up/Down cursor keys or wheel to trim. |
| Soft Keys |
|
| Soft Keys |
Enables the knob buttons on the channel strips to become softkeys. See the Assignable Keys tab for the Soft Key entries and how to map them in the Cubase Studio Setup window. |
| View Buttons |
|
| Focus |
Toggles Banking mode follow for Bank and Scroll buttons. |
|
When Follow mode is on, Mixer in Cubase moves to match what is shown on Control surface. (Must have track count in Cubase view match control surface layout.) |
These keys are listed in the Cubase / Nuendo Studio Setup window when the C|24 is selected. V-Control Pro assigns each one a default command. You can change any of them to any Cubase command, and keys listed as Not assigned do nothing until you assign one.
To change a key, open Studio / Studio Setup, select the C|24, then set the Category and Action for that key.
| Key |
Default Category |
Default Action |
| Mix Window |
Devices |
Mixer |
| Status Window |
Devices |
VST Performance |
| Plug-In Window |
Windows |
Show/Hide Plug-ins |
| Pan Window |
Automation |
Open Panel |
| Edit Window |
Transport |
Panel |
| Transport Window |
Transport |
Panel |
| Mem-Loc Window |
Project |
Open Markers |
| Alt Window |
Automation |
Open Panel |
| Write Auto To All |
Automation |
Fill Loop |
| Zoom Preset 1-5 |
Not assigned |
Not assigned |
| Soft Key 1-24 |
Not assigned |
Not assigned |
| V-Window Mode |
|
| With the V-Window feature, users can instantly control any plug-ins or controls on screen through their control surface's channel strip with a touch of a button. |
|
| Master Fader |
Press once to enable Master Fader control. Press a second time to enable V-Window mode for the 24th channel fader. Press a 3rd time to cycle back to basic channel control. |
| Mute |
While in V-Window mode, the Mute button on the last channel strip will cycle through the various V-Window Modes which are listed below: |
|
VButton: Use this mode to interact with button controls. The mouse will stay in its place and activate a button press when the fader is touched. |
|
VButtonSet: Use this mode to create and cycle through different button set points. With the mouse hovering above the on screen button's position press Shift+Solo on the control surface to set a Pin at that location. Using the fader in this mode will cylce between multiple Pins to use with VButton mode. |
|
VWKnob: Use this mode when interacting with knob controls on the plug-ins GUI. |
|
VWHSlider: Use this mode when interacting with horizontal slider controls on the plug-ins GUI. |
|
VWVSlider: Use this mode when interacting with vertically slider controls on the plug-ins GUI. |
| Solo |
While in V-Window Mode, pressing the Solo button will pin the mouse location and revert to that location any time the fader is touched. Once the fader is released, the mouse is also returned to that pin position. This way it is very easy to pin a parameter and instantly control it without having to worry with the mouse cursor is on the screen. |
| Select |
Use the Select button while in V-Window mode to reset the fader position. |
| MIDI Mode |
|
| MIDI Mode converts the surfaces faders, knobs, and buttons into assignable MIDI Controls that can be mapped in the DAW. |
|
| Focus |
Toggles surface between DAW Mode and MIDI Mode |