| Channel Strips |
|
| Record |
Arms the assigned audio track of the Channel. |
| Solo |
Solos the Channel. |
| Mute |
Mutes the Channel. |
| Select |
Sets the Channel to the Select state. Acts as Record enable when the record button is enabled. |
| Knob |
Changes the assigned parameter. |
| Record |
Toggles Record enable mode for channel select buttons. |
| Meter |
Toggles meter display to left or right meter. |
| Track Meters |
Displays Stereo metering for tracks. |
| Bank Mode |
|
| The assignment buttons are used to assign controls to the Knobs. |
|
| Pan (Default) |
Shows pan position in LED Strip. Knob controls pan position. |
| Send A |
Assigns Send 1 to knobs. Assigns Send 6 to knobs when current assignment is Send 1. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send B |
Assigns Send 2 to knobs. Assigns Send 7 to knobs when current assignment is Send 2. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send C |
Assigns Send 3 to knobs. Assigns Send 8 to knobs when current assignment is Send 3. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send D |
Assigns Send 4 to knobs. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send E |
Assigns Send 5 to knobs. Use Channel Bar Scroll Left and Right to switch parameters. |
| Send parameters |
1st parameter is Send level. |
|
2nd parameter is bypass for Send assignment. |
|
3rd parameter is Pre/Post. |
|
4th parameter is pan for send. |
|
5th parameter is Send assignment. |
|
6th parameter is Master send bypass for channel. |
| Monitor |
Assign channel parameters to knobs. Use Channel bar scroll Left and Right to cycle through parameters. |
| Channel Parameters |
1st parameter is channel output. |
|
2nd parameter is input monitoring on channel. |
|
3rd parameter is channel input. |
|
4th parameter is pre-gain. |
|
5th parameter is phase invert. |
| Insert |
Assigns knobs to edit selected track's inserts. |
| Flip |
Flips knobs to faders. |
| Master Faders |
Enables Master Fader control on the 7th channel of Command |
| Automation |
|
| Write |
|
| Read |
|
| Touch |
|
| Latch |
|
| Transport |
|
| Play |
Starts playhead at current position in Timeline. |
| Stop |
Stops playhead at current position in Timeline. |
| Record |
Starts Record Mode for playhead |
| Rewind |
Move playhead backwards in Timeline. |
| Fast Forward |
Moves playhead forward in Timeline. |
| RTZ |
Returns playhead to beginning of Timeline. |
| Shift+RTZ |
Sends playhead to end of Timeline. |
| Loop Play |
Toggles Loop mode for loop selection in Timeline. |
| Quick Punch |
Toggles Punch mode for selection in Timeline. |
| Counter |
Displays Counter for current session. Counter mode can be changed in DAW. |
| Utility |
|
| Undo |
Undo the last action. |
| Shift+Undo |
Redo the last action. |
| Save |
Save the current session. |
| Window Buttons |
|
| Mix |
Opens MixConsole Window |
| Navigation |
|
| Bank Left |
Banks tracks left/Scrolls 1 track left in Nudge mode |
| Bank Right |
Banks tracks right/Scrolls 1 track right in Nudge mode |
| Nudge |
Toggles Nudge mode On/Off |
| There are several different modes available for the cursor keys and wheel. |
|
| MemLoc |
Enables Marker Mode. Use Wheel or Left/Right cursor keys to navigate between markers. Down cursor key creates marker at playhead. |
| Zoom |
Enables Zoom mode for the wheel and cursor keys. |
| Zoom+Shift |
Enables Track Zoom for the wheel and cursor keys. Track zoom increases/decreases track height. |
| Zoom+Option |
Enables Wave Zoom for the wheel and cursor keys. Wave zoom increases waveform view in region. |
These keys are listed in the Cubase / Nuendo Studio Setup window when Digidesign 003 is selected. V-Control Pro assigns each one a default command. You can change any of them to any Cubase command, and keys listed as Not assigned do nothing until you assign one.
To change a key, open Studio / Studio Setup, select Digidesign 003, then set the Category and Action for that key.
| Key |
Default Category |
Default Action |
| Save |
Devices |
Mixer |